Fortinet/CLI: Unterschied zwischen den Versionen

Aus SchnallIchNet
Wechseln zu: Navigation, Suche
 
(Eine dazwischenliegende Version desselben Benutzers wird nicht angezeigt)
Zeile 63: Zeile 63:
 
end
 
end
 
</pre>
 
</pre>
 +
 +
 +
=== policy routes ===
 +
 +
<pre>
 +
show router policy
 +
...
 +
    edit 76
 +
        set input-device "port7"
 +
        set src "1.2.3.4/255.255.255.255"
 +
        set dst "192.168.0.0/255.255.0.0"
 +
        set output-device "port1"
 +
    next
 +
    edit 77
 +
        set input-device "port7"
 +
        set src "1.2.3.4/255.255.255.255"
 +
        set dst "0.0.0.0/0.0.0.0"
 +
        set gateway 4.3.2.1
 +
        set output-device "wan2"
 +
    next
 +
end
 +
</pre>
 +
 +
to set new policies, pick a new number and use:
 +
 +
config router policy
 +
  
  
Zeile 117: Zeile 144:
 
  diag sys session clear
 
  diag sys session clear
  
[http://kb.fortinet.com/kb/viewContent.do?externalId=FD30038]
+
[http://kb.fortinet.com/kb/viewContent.do?externalId=FD30038 Fortinet-Docu]

Aktuelle Version vom 26. Juni 2017, 09:26 Uhr


CLI

Address Objects

show firewall address | grep -i PATTERN
edit "Hostobject"
       set comment "bla"
       set associated-interface "wan2"
       set subnet 1.2.3.4 255.255.255.255
next
show firewall addrgrp "GRP Name"
config firewall addrgrp
    edit "GRP Name"
        set member "Hostobject 1" "Hostobject 2" "Hostobject X" ... 
    next
end


Policy

config firewall policy
    edit 81
        set srcintf "port1"
        set dstintf "wan1"
        set srcaddr "Netz1" "Netz 2" "Netz ..."
        set dstaddr "Netz - DST"
        set action ipsec
        set schedule "always"
        set service "ALL"
        set logtraffic all
        set natip 10.x.y.0 255.255.255.0
        set comments "ACHTUNG NAT-Adresse via CLI hinzugefuegt"
        set outbound enable
        set natoutbound enable
        set vpntunnel "PH1NAME"
    next
end

config firewall policy
    edit 238
        set srcintf "port7"
        set dstintf "wan1"
        set srcaddr "NETZ SRC"
        set dstaddr "Netz DST"
        set action ipsec
        set schedule "always"
        set service "ALL"
        set logtraffic all
        set natip 10.x.y.0 255.255.255.0
        set comments "Outbound NAT!  set natip 10.x.y.0 255.255.255.0"
        set inbound enable
        set outbound enable
        set natoutbound enable
        set vpntunnel "PH1NAME"
    next
end


policy routes

show router policy
...
    edit 76
        set input-device "port7"
        set src "1.2.3.4/255.255.255.255"
        set dst "192.168.0.0/255.255.0.0"
        set output-device "port1"
    next
    edit 77
        set input-device "port7"
        set src "1.2.3.4/255.255.255.255"
        set dst "0.0.0.0/0.0.0.0"
        set gateway 4.3.2.1
        set output-device "wan2"
    next
end

to set new policies, pick a new number and use:

config router policy


Show IPSec VPN config

Phase1:

show vpn ipsec phase1-interface

Phase2:

show vpn ipsec phase2-interface


Packet Capture

tcpdump

diag sniffer packet "<interface-name|any>" "host <IP> and port 3389" 4

4 = verbose level (1-6)

Fortinet-Docu


Firewall Session debugging

 diag debug enable
diag debug flow filter add <PC1>    or    diag debug flow filter add <PC2>
diag debug flow show console enable
diag debug flow trace start 100          <== this will display 100 packets for this flow

debugging beenden:

diag debug flow trace stop


One further step is to look at the firewall session. For this, some filters may be used to reduce the output; see the following example:

diag sys session filter src PC1
diag sys session list

or

diag sys session filter dst PC1
diag sys session list


To clear all sessions corresponding to a filter:

diag sys session filter dst PC1
diag sys session clear

Fortinet-Docu